Advanced Materials, Processing and Testing Technology II [Mīkstie vāki]

Preface
Chapter 1: Properties and Processing Technologies of Steel and Alloys
Microstructure and Mechanical Properties of W-High Entropy Alloy Composite by
Hot Swaging
Analysis of the Crack of 304 Stainless Steel and Improvement Measures
Analysis of Microstructure and Properties of High Strength Steel for Vehicle
Axle
High-Throughput Characterization of Composition and Performance of Titanium
Alloys Based on Nanoindentation Technology and EPMA
Influence of Mould Slenderness Ratio on the Solidification of Heavy Ingots by
Numerical Simulation
Quantitative Characterization of Heat Treatment Response in a Single Crystal
Nickel-Based Superalloy
Effect of Tempering Process on Microstructure and Mechanical Properties of
Low Alloyed Cast Steel
Study on Fatigue Crack Growth of Laser Melting Deposited 12CrNi2 Alloy Steel
Based on XFEM
Microstructure and Mechanical Properties of Low Alloy Ultra-High Strength
Steel Microalloyed with Cerium
Influence of Riser Necking Ratio and Taper on the Solidification of Heavy
Ingots by Numerical Simulation
Research on Deformation Prediction Method of Laser Melting Deposited
Large-Sized Parts Based on Inherent Strain Method
Research on Springback during Hot Stamping with Uniform and Local-Thickened
Sheet Blanks
Experimental and Numerical Analyses of Tubular Electrohydraulic Forming
Process
Effect of Annealing Temperature on Microstructure and Properties of Cold
Drawn Tube
The Studies of Irradiation Hardening and RIS on IASCC of Reactor Internals
Bolts
Yield Behavior of Tube Hydroforming and its Effecti on Hollow Component
Manufacturing
Chapter 2: Surfaces and Special Coatings
The Coatings Formation and Characteristic of a Low Pressure Thermal Plasma
Torch
Preparation of WC/Ni Flexible Cloth Coating by Vacuum Brazing
Researching Advances in Application of Bio-Inspired Superhydrophobic Metallic
Surface
Microstructure and Property of Novel -Fe/ (Cr, Fe)7C3 Lamellar Eutectics
Reinforced Composite Coating
Chapter 3: Properties and Processing Technologies of Special Structural and
Functional Materials
The Effect of MgO Stabilizer on the Phase Composition and Microstructure of
Zirconia Metering Nozzle Matrix
The Influence of Rapid Prototyping Technology on Optimization of Automobile
Energy-Absorbing Box
Effect of High Temperature Treatment in Ar Atmosphere on the Tensile Strength
and Structure of SiC Fiber
Effect of Tensile Stress on Characteristics of High-Temperature
Superconducting Tape
Preparation of Fe-Cu-Based Friction Material and its Adoption in Automobile
Mechanical Mechanism
Cutting Behavior of Self-Lubricating Ceramic Tool in Dry Machining of 40Cr
Quenched Steel
Thermal Behaviour in the Stereolithography Process for Al2O3 Ceramic
Suspension
A High Thermoelectric Performance ZT in p-Type LaSe2 Crystal
Chapter 4: Properties and Application of Polymers and Composites
Research and Prospect of Diamond/Aluminum Matrix Composites
Optimal Design of Composite Material Maintenance Structure for Aircraft Based
on ANSYS Workbench
Study on Preparation of Novel Dicyclopentadiene Phenol Epoxy Resin Materials
Based on Different Degrees of Polymerization
Performance Improvement of Carbon Fiber Reinforced Epoxy Composite Sports
Equipment
Preparation and Mechanical Properties Analysis of Aviation Mechanical Carbon
Fiber Reinforced Plastics
Chapter 5: Materials and Technologies for Electronics
The Distribution Trend of Boron Atoms in Semiconductor Silicon under High
Temperature
RETRACTED: Fractal Structure in Poly(3-Alkylthiophene) Derivatives
First-Principles Study of Ag3Sn, AgZn3 and Ag5Zn8 Intermetallic Compounds
Fabrication and Investigation on the Polyimide/Al2O3 Composite Films via Ion
Exchange Technology
Research on the Magnetron Sputtering Performance of Active Matrix Liquid
Crystal Display Electronic Materials Based on Amorphous Oxide Thin Film
Transistors
Effect of Laser Processing Parameters on Microhole Quality of Aluminium
Nitride Ceramics
Effect of Reaction Temperature and Mixture Ratio on Polysilicon Production
Process
Chapter 6: Chemical Technologies and Chemical Production
A Preparation Method of -Carotene Reference Standard from -Carotene Food
Additive Based on High Speed Countercurrent Chromatography (HSCCC)
Research on the Stability of Pd-Based Multi-Component Supported Catalysts
Study on Electrochemical Oxygen Evolution Properties of Bimetallic Carbon Nan
Sheets
Research Progress of N-Alkylation of Alcohol and Amine by "Hydrogen
Reaction"
Chapter 7: Building Materials and Structural Elements
Stress Loss of Pre-Tensed CFRP Strips Strengthening Square R Column
Performance Test of C60 Self-Compacting Steel Fiber Concrete
Model Test of Steel-Concrete Composite Beam Deck under Negative Moment
Effect of Initial Consolidation Stress Path on Shear Behavior of Calcareous
Sand
Study on the Development and Performance of a New Concrete Antifoaming Agent
Study on Porous Structure of Porous Media in Geotechnical Materials
Asphalt Modified by Ethylene-Acrylic Acid Copolymer Ionomers: Fundamental
Investigations of Mechanical and Rheological Properties
Synthesis, Characterization and Application of a Potential Chemical
Sand-Fixing from Lignin Sulfonate Graft Urea-Formaldehyde Resin
A Novel Approach to Characterize the Quantity and Distribution of
Microorganisms in Microbial Self-Healing Cementitious Materials