Technology of Plasticity [Mīkstie vāki]

Preface, committee, organizers and sponsors
Chapter 1: Research and Development of the Metal Forming Technologies and
Processes
Drawing Force Optimization Research on Forming Parameters of Drawing Wire Rod
with Rotating Die under Coulomb Friction
Finite Element Analysis of Rolling Process to Locally Thin Metal Strips
Experimental and Numerical Analysis of Titanium Alloy Microtube Tube-End
Nosing Forming
Finite Element Simulation of Rotating Compression Forming
Dry Progressive Stamping of Copper-Alloy Snaps by the Plasma Nitrided
Punches
Grain Size Effect on Optimum Clearance Determination in Blanking Non-Oriented
Electrical Steel Sheet
Process Analysis of Fabricating Elbow Tubes by Mandrel Bending Process
The Effect of Flange Length on the Distribution of Longitudinal Strain during
the Flexible Roll Forming Process
Dimensional Characteristics of Tailor Rolled Blanks Having Thickness
Variations both in Longitudinal and Width Directions
Mechanical and Microstructural Evolutions of the Laser Deposited Titanium
Layers under Various Shielding Atmospheres
Deep Drawability of Ti/Steel/Ti Laminated Sheets
Study the Influence of Geometric Parameters on Springback in T-Section
Aluminum Alloy Window Trim Strip Sheets Forming
Research on Single Pass Deep Drawing Spinning Formability of Cup-Shaped
Parts
Influence of Laser Shot Peening Parameters on the Surface Hardness and
Roughness of 7075 Aluminum Alloy
Investigation of a Two-Step Rotary Rim-Thickening Process of Disc-Like
Blanks
Study on Thickness Distribution and Spring Back Phenomena of Sheet-Bulk
Forming for Aluminum Alloy
Investigation on Dynamic Impact Effect of Ultrasonic-Assisted Compression
Test
Study on Multi-Step Spinning Process for Disk-Like Part with Thickened Rim
Micro-Drawing of Circular Cups with Thin Stainless Steel Sheets
Optimizing Design of the Cutting Tool in Cutting of Ultra-High Strength Steel
Beam Part
Geometric Design of Rectangular Cross-Sectional Springs
The Numerical Simulation and Experiment Verification of the Large Aluminum
Alloy Covering Part of Car Using Sequential Coupling Technology
Evolution of White Layer during Wire-Cutting and Comparison of Several
Methods to Improve Surface Integrity for Fineblanking Tools
Warm Bulge Forming of Small Diameter A1100 Aluminium Tube
Analysis of Dieless Drawing to Form the End of Metal Wires under Proportional
Shape Evolution with Slab Method
Plasma Printing of Micro-Punch Assembly for Micro-Embossing of Aluminum
Sheets
Chapter 2: Materials Properties Analysis, Measurement and Numerical Modeling
Comparing Two Selection Laws of Active Slip Systems in Finite Element
Polycrystalline Model for Numerical Material Testing
Influence of the Friction Factor on the Temperature Field in Upsetting of a
Perfectly Plastic Strip under Plane Strain Conditions
Prediction of Shear Length in Blanking Process by Numerical Analysis
Numerical Biaxial Tensile and Tension-Compression Tests of Aluminum Alloy
Sheet Using Crystal Plasticity Finite Element Method
Ideal Flow Theory of Pressure-Dependent Materials for Design of Metal Forming
Processes
Design of Flexible Bulge Testing System for Evaluating the Influence of Size
Effect on Thin Metal Sheets
Application of FEM and Abductive Network to Determine Forging Force and
Billet Dimensions of Near Net-Shape Helical Bevel Gear Forging
Characterizing of Anisotropy and Asymmetry of Tubular Materials
Tensile and Compression Analyses to Investigate the Mesoscale Mechanical
Characteristics Influential for Press Formability of CFRP Sheets
Effect of Strain Path Change on Formability of TRIP Steels
Effect of Different Processes on Hydrogen Storage Properties of AZ Magnesium
Alloy
Microstructure and Texture Evolution of 2024 Aluminum Alloy Sheet under
Different Loading Conditions
Hot Deformation Behavior of Al-Cu-Li-Mg-Zn-Zr-Sc Alloy in As-Cast and
Hot-Rolled Condition