Manufacturing Process Technology [Mīkstie vāki]

Sponsors, Committees, Preface
1 Surface Engineering / Coatings
Ultrasonic Elliptical Vibration Turning Studty for Precision and
Ultra-Precision Workpiece
Experimental Research on Improving Wear Resistance of Coating Surface by
Magnetron Sputtering
The Study on Metallurgical Property of 380m3 Blast Furnace Slag of YIGANG
Research in Vacuum Diffusion Bonding of Ti-6Al-4V Alloy and Type 25 Low
Carbon Steel
The Influence of Alloying Additives on the Machinability of Austenitic
Stainless Steel
The Spray Angle Improvement of Single Inlet Pressure Swirl Atomizer Using
Partial Structure Modifying
Study on Friction and Wear Behavior of GCr15/1045 Steel under Nano-Particle
Additive Conditions
The Study of Hole Injection in OLEDs with Ultra-Thin Sol-Gel TiO2 Layer
Mass Customization Management in E-Commerce Configuration with early Supplier
Involvement
Prediction of 3D Cavity Hydrodynamic Noise Based on Equivalent Source Method
Numerical Simulation of the Effects of Cell Size on the Mechanical Property
of Microcellular Polypropylene
Sliding Friction and Wear Test of TiAlN TiN Films and 40Cr Steel
Computer Simulation on Mo/Al2O3 Solar Energy Selective Absorbing Coating
Effect of Two-Step Deforming and Aging Process on the Properties and
Microstructure of Cu-Cr-Zr-Mg-Si Alloy
Effect of Pre-Shot Peening on the Fretting Fatigue Behavior of Plasma
Nitrided AISI 420 Stainless Steel at 350 °C
Microstructural Study of Nanostructured ZrO2 Based Thermal Barrier Coatings
Fabricated by High Efficiency Supersonic Plasma Spraying
Influencing Factors of AZ31B Sheet Deep Drawing
Preparation of ZrTiN Hard Coating and its Performance
Application of Monte Carlo Method in the Measurement Process Design According
to next Generation of GPS
Integrated CAD System for Bridges Based on BrIM
Effects of TiO2 on the Viscocity and Solidification Temperature of Mold
Fluxes for the Stainless Steel
Contact Analysis for Joint Interfaces of Machine Tools Based on a 3-D
Anisotropic Asperity Model
Grinding Performance of Permeated Grinding Wheel
Investigation of the Effects of Dielectric Inlet Pressure in Inner Jetted
Dielectric EDM Milling
Research on the Adhesion of Stainless Steel Film on Gd by Magnetron
Sputtering
Oxidation Resistance of CrN and CrAlN Coating Tools
Research on Producation of a New Type of Biological High Molecular Material
Poly(-Glutamic Acid)
Industrial Preparation of SiC Ceramic Coating for High Temperature and
Anti-Oxidation of C/C Composites
Influence of Friction on the Vibratory Response of Structure
Microstructures, Thermal Shock Resistance and Isothermal Oxidation Resistance
of Nanostructured Ceria Stabilized Zirconia Coatings
Application of Repair and Anti-Corrosion Technology on Reinforced Concrete
Structures of a Domestic Wharf
Study on High-Temperature Oxidation Characteristics of Pure Vanadium
Friction and Wear Characteristics of Electrodeposited Ni-MoS2/Al2O3 Composite
Coating
Influence of Liquid Phase Migration on Intermittent Extrusion of Aqueous
Al2O3 Paste
On the Dispersants of Diamond-Ni-P Composite Electroless Plating and
Properties of the Coating
High Temperature Oxidation Behavior of (Ti, Al) C Ceramic Coatings on Carbon
Steel Prepared by Electrical Discharge Coating in Kerosene
Study on Contractive Rate Inspecting Testing Mould of Thermoplastic
Comparison of Different Content of Cd and Sb Element on the Microstructure,
Mechanical Properties of As-Cast AZ31 Magnesium Alloy
Evaluation Equation of the Flat Compression Properties of Corrugated Sandwich
Structure
Study on Active Screen Plasma Carburizing of Austenitic Stainless Steel
The Bifurcate Fracture Analysis of Linear Red Copper Penetrator
Fabrication of PET Fabric/Ni-Fe-B Alloy Composite through a Electroless
Plating Process with a Novel Activiting Method
Biocompatibility Research of Medicine Titanium Alloy Coating by Microarc
Oxidation
Design of Virtual Oscilloscope Based on S3C2410
Research on Lubrication and Wear-Resistant Mechanism of Ni60A/MoS2 Composite
Coating
Study on the Mechanism of Improving the Formability of DP Steel LTWB at the
Elevated Temperature Level
The Simulation and Experimental Study of Metal Cutting Based on Cold Air
Technology
Tribological Performance of Fabric Composites Filled with Nano-Additive under
Varied Load Conditions
Polymer Cement Waterproof Coating and its Properties
Corrosion Characteristics of PEO Films on AZ31 Magnesium Alloys
Numerical Simulation of Casting Process for Gray Iron Butterfly Valve
Nickel-Diamond Compound Electroless Plating on Cast Aluminum Alloys
Process Research on High-Speed Small Hole Drilling by EDM Combined with
Magnetic Field and Water Dispersant
Preparation and Oxide CMP Performance of Inorganics Coated Polystyrene
Composite Particles
EIS Study of Molybdate Conversion Coatings Formed on AZ91D Magnesium Alloy
Microstructure and Properties of FeAl/Cr3C2RE Composite Coating Produced by
HVFS
The Measurement for the Effective Anisotropy Constant of the Nanocomposite
Permanent Magnetic Material Nd2Fe14B/-Fe
Development of Visualization System for Aircraft Assembling Process Oriented
Assembly Field
The Crystallization Characteristics of Carbon Nanotubes/Pb-Sn Composite
Coatings
Study of Microstructure and Adhesion Strength of WC-Co Coating Sprayed by
High Velocity Oxygen Fuel
Performance and Property of Ni Base Coatings by Using Plasma Arc Technology
for 18Cr2Ni4WA Steel Repairing
Energy Consumption and Emissions Analysis of Natural Gas Exploitation
High Temperature Erosion Behavior of Mo-Si-Ni-Al Metal-Ceramic Composite
Cladding Layer Produced by TIG Welding
Rheological Fracture Analysis of Beam
The Effect of Complexing Agent on the Surface of Aluminum Alloy Plating Ni-P
Alloy
Polyhedral Oligomeric Silsesquioxane/PDMS Hybrid Coating Protecting Polyimide
from Atomic Oxygen Erosion
Finite Element Analysis for Temperature Field of Laser Remelting Plasma
Sprayed Ni-Based Gradient Coating on Ti6Al4V Alloy Surface
The Effect of NaOH on the Surface of Magnesium Alloy Ni-B Alloy Plating
Properties
Temperatures Effection to Electroplating Ni-SiC Plating on Aluminum Alloy
pHs Effection to Electroplating Ni-SiC Plating on Aluminum Alloy
Preparation and Performance of Compound Polyurethane Foam Plastic Board for
Freezing Prevention in Channel Lining
Effect of Carbon Fiber on Composites
The Experimental Analysis of Modifier on Fluid Magnetic Abrasivetool
The Research on Coating of Electroless Ni-W-P Ternary Alloys
Advanced Monitoring of Tool Wear and Cutting States in CNC Turning Process by
Utilizing Sensor Fusion
The Bending Behavior of Surface Composite Layer Ni/WC Fabricated through
Vacuum Infiltration Casting
Structural Reinforced Parts for Improving Roof Crush Performance
Study on Morphologies and Structures of Ceramic Coating Prepared by Micro-Arc
Oxidation on TC4 Alloy
Preparation by Electroless Plating and Electromagnetic Shielding
Effectiveness of Ni-Cu-Coated Calcium-Magnesium Silicate Whisker
Arsenic Removal from Wastewater Using Adsorptive Mediums
Preparation and Characterization of Al2O3/ZrO2-MgO-CeO2 Composite Coatings
Prepared by Flame Spraying
Efficiency-Reinforcement Design of Hydraulic Reciprocating Sealing Driven by
Ideal Solution
Photocatalytic Degradation of Polycyclic Aromatic Hydrocarbons on Soil
Surfaces Using Fe2O3 under UV Light
The Optimization Analysis of Equipment Maintenance Based on Monte-Carlo
Simulation
Study on Salt Fog Corrosion of FeCoCrMoCBY Amorphous/Nanocrystalline Alloy
Coating
Influence of the Section Plane Position on the Performance of Power
Ultrasonic Transducer
Effect of Heat Treatment on Structure and Hardness of Electroless Ni-P
Plating
High Temperature Oxidation Behavior of NiAl and Ni3Al Argon Arc Claddings
Influence of Temperature and Oxygen Pressure on the Oxidation Process for
Preparing Tritium Permeation Barrier
Rheological Behavior of Polymethyl Methacrylate (PMMA) Filling through Micro
Channels
Preparation and Properties of Electroless Deposited Ni-Sn-P Ternary Alloy
Coatings
Residual Stress State of TIG Remelted Zone in the Weld Toe after Chilling
Treatment
Realization of the Closed Cycle Diesel Control System
Slip Fascia Stiffness Effect to the Fifth Metatarsal Movement during
Inversion Landing
Structure of Emulsion Cavitation Jet and Jet Peening Impact on the Fatigue of
Plan Carbon Steel Q235A
Parameter Design and Result Analysis for Radial AC Hybrid Magnetic Bearing
Effect of SnO2 Modification on Permeate Flux of -Al2O3 Microfiltration
Membrane for Treating Fe(OH)2 Suspensions
Experimental Study on Tungsten Leaching from Cemented Carbide
Microstructure and Cavitation Erosion Behavior of Carbide-Based Coating
Deposited by Electrical Arc Spraying
Preparation and Properties of Weldable Self-Cleaning PVDF/PVC Blended Film
Analysis on the Anodic Oxide Film of Aluminum Pistons Formed in High Current
Density and Wide Temperature Range
Study of TI64 Vibration Laser Metal Deposition Process

In situ Synthesis of Ceramic Phase Reinforced Fe-Based Alloy
Surface Coating by PTA
Cavitation Erosion Characteristics of an Iron-Based Coating Prepared by High
Velocity Arc Spraying
Microstructure and Properties of Mo2FeB2 Cermet Coating by Induction Heating
Influencing on Structure and Mechanical Properties of PA6/PP Blends for
Different Graft Yield Compatibilizer
Optimization and Design for Parameter in Injection Molding Technology of Cell
Shell of Polypropylene
The Research on Deformation Analysis of Rigid Packed Hole Assembly Dynamic
Model in 3D Borehole
A Novel Tetrahedral Mesh Generation Algorithm for Finite Element Analysis
Tooth Surface Bi-Directional Envelop Machining Method of Involute Arch
Cylindrical Gear
Improvement on the Manufacturing Process of the Dental Surgical Guide Made by
a 5-Axis CNC Drill Press
Influence of Current Density on Structure and Performance of Micro-Arc
Oxidation Coatings on AZ31 Magnesium Alloy
Research of Compress Anti-Surge Based on the Integral Separation PID
Algorithm
Effect of High-Intensity Pulsed Ion Beam Irradiation on the Electrochemical
Corrosion Behavior of AZ31 Magnesium Alloy
Preparation of LaNi5 by FFC Cambridge Process
Preventing Sintering Bricks of Purple Sandy Shale from Lime Brust:
Experimental Research on Fixing Calcium with Sulfur
Preparation and Application of Oxygen Quenching Pressure Sensitive Paints
Research of Radial-Axial Ring Rolling Process Curve
Technical Problems to be Solved in Outside Surface Galvanized and Inside
Surface Plastic Coated Steel Pipe for Main Gas Pipe Line
Experimental Study on Wear Resistance of Engine Cylinder Based on Surface
Hardening Technology
Study on Relationship between the Groove Structure and Efficiency of
Electromagnetic Pump Used in Aluminum Alloy Casting
Dispersion of Carbon Fibers in the Hybrid Fiber Cement-Matrix Composites
The Experimental Study on Grinding Properties of Gas Quenching Steel Slag
The Design and Analysis of Nozzle
Room-Temperature Ferromagnetism in Ni-Doped Na0.5Bi0.5TiO3 Crystals
The Study on the Precipitation Behavior of the Second Phase Particles for
As-Hot Rolled Dual-Phase Nb-Bearing Steel
Film Formation Property of Mineral Particles as Grease Lubricant Additives at
Different Friction States
Semi-Encasing Sucrose Ester and Grafting Silkworm Pupae Protein on Polyester
Fabric to Modify Polyester Fabric Surface
Placement Optimization for Thermal Performance of Embedded Power Chip
Microwave Modules Using BP-GA
Preparation and Optical Property of Mn-Doped ZnO Nanorods
Chemical Vapor Deposition (CVD) of ZrC Coatings from ZrCl4-C3H6-H2
Surface Characterization of Chinese Fir/TiO2 Composite
Research about Relationship of Laser Quenching GCr15 Steel Bending Properties
and Hardening Layer Fracture Fractal Dimension
Analysis and Solution of Hydraulic Cylinders Leakage Problem
Structure and Property of CrAlN Coatings Prepared by Bipolar Pulsed Dual
Magnetron Sputtering (BPDMS) under Different Pulse Bias Voltage
Corrosion Resistance of Al2O3-ZrO2 Composite Coating by Microarc Oxidation on
2A12 Aluminum Alloy
Optimum Autoclaved Cement Concrete Mix Design Based on Flexural Strength
Comparison of Surface Roughness Measurement in Dichromatic Speckle Patterns
with Autocorrelation Method
Study of Double-Polar Micro-Arc Oxidation Ceramic Layers on Aluminum Alloy
Microstructure and Phase Composition of Iridium Coating on Molybdenum after
Heat Treatment at 1400°C
Experimental Study on the Through-Mask Electrochemical Micromachining (EMM)
Process
Numerical and Experiment Analysis of Rail Wear
The Lightweight Design on the Pressure Hull of Underwater Gliders Using
ANSYS
Microstructure Characterization and Abrasive Wear Performance of HVOF Sprayed
WC-Co Coatings
Influence of Different Wave-Lengths Artificial Light on Surface Discoloration
of Dyed Veneer
The Application and Research for Estimation Method of Turning Cost
Influence of Electric Field Interference on Three Nozzles Electrospinning
Inheriting of Traditional Culture in Design
Functional Evaluation Software Design of Surface Topography Based on MATLAB
Research on Stress Calibration Technology on Aluminum of High-Speed Train
Body Structure by Nondestructive X-Ray Method Measurement
The Research about Oxidation Kinetics of Ti60 Alloy and Ni-Co-Cr-Al-Y-Si
Coating on Surface
Enhancement of the Service Lifetime of TiN Coated Punch Side pin by Adding a
Small Amount of Yttrium
500MPa Seismic Rebars Developed by Nitrogen-Rich and Vanadium-Microalloyed,
Controlled Cooling Technology
Thermal Effects of Aluminum Nitride
Study on the Incline Limit in Gas Metal Arc Welding Based Rapid Forming
Laser Cladding In Situ Tungsten Carbide Reinforced Ferrous Matrix Surface
Composites
Study on Rapid Manufacturing of CAFÉ Injection Mold
The High-Temperature Oxidation Behavior of the Fe-Ni Based Alloy Coating
Produced by Plasma Cladding
Anodic Aluminum Oxide Matrix Encapsulating Nonivamide for Anticorrosion and
Antifouling Application
Study on Structure and Properties of Alloy Nodular Cast Iron Roller with
Laser Heat Treatment
A Study on Dieless Incremental Sheet Metal Forming Using Water Jet
Technology
Solid Modeling and Machining Approach of the Impeller Based on Five-Axis
Machine Tool
Characterization and Corrosion Studies of Amorphous/Nanocrystalline
Conversion Coatings Formed by Applying Static Magnetic Field on AZ91 D
Magnesium Alloy
Direct Current Field Effect on Silicon Pack Cementation for 1045 Steel
The Initial Practice on Electro-Modification Processes to Al-12Si Alloys
The Influence of Coating on the Elastic Modulus of Basalt Filament Diaphragm
Fabric
An Evaluation Model of Enterprise Informatization Level Based on Grey
Whitenization Weight Cluster Analysis
Effect on Microstructure and Hardness of Plunger Piston of Fe-Based Composite
Coating by Laser Cladding
Research on the Microstructure and Wear Resistance of Hardfacing Layer on Big
Cold Trimming Die Insert
Study of the Ce-Mn Conversion Coating on 6061 Aluminium Alloy
The Finishing of Rolling Bearing Raceway by Electrochemical Mechanical
Finishing (ECMF) Technology
Research on Factors Affecting Durability and Improvements for FRP Reinforced
Concrete Structures
Study on the Mechanical Properties of PP/EPDM/Mesoporous MCM-41 Composites
A Hard and Thick Fe-Based Amorphous Composite Coating
Study on Extraction of Dioscin from D.zingiberensis
Microstructures and Properties of Laser Al Alloying on AZ31 Magnesium Alloy
Effect of Direct Current on the Semi-Solid Isothermal Heat-Treated
Microstructure of ZA84 Magnesium Alloy
Observation and Removal of Atmospheric Micro-Contaminants on SUS304 Steel
The Real-Time Monitoring Tool States Based on Wavelet Analysis
Study on the Acquisition Method of a Digital Model for Oral Cavity Teeth
Based on Point Cloud
Growth Process and Corrosion Resistance of Ceramic Coatings of Micro-Arc
Oxidation on Mg-Nd Magnesium Alloys
Effects of Ultrasonic Deep Rolling on Fatigue Performance of Pre-Corroded
7A52 Aluminum Alloy
CrN Films Deposited by Middle Frequency Magnetron Sputtering
Low Cost Vibrometer Utilizing Laser Diode Self-Mixing with Sound Card
Controlled by LabVIEW
Effect of Saccharin Addition on the Electrodeposition of Nickel from a
Watts-Type Electrolyte
The Micro-Mechanical Behavior of Inclusions under Tensile Load in X80
Pipeline Steel
Effect of Cold-Rolled Process Parameters on Deep-Drawing Performance of
Micro-Carbon Steel
Study on Low Temperature Deposition of TiN Films and their Tribological
Properties
Influence of Voltage Parameters on Formation Process of MAO Ceramic Coating
on Aluminum Alloy
The Evaluation of NHW-1 Type Coated Tubing Abrasion Resistance Performance
Effect of Equal Channel Angular Pressing on Microstructure and Dislocation
Strengthening of 3003Al Ingot
Design of the Range-Measurement System for Mobile Robots Based on ARM
Numerical Simulation of Impact Process of Coal and Gangue
Errosion-Corrosion Critical Performance of Surface Nanocrystalline 20 Carbon
Steel in Condensate Water
Corrosion Behavior Research of Fe3Al Intermetallic Compound in H2S/CO2
Environment
Study on the Structure of Grind-Hardened Layer and Parameter of Hardening
Depth of 42CrMo Steel
Study on Rollers Angular Velocity Matching of Rolling Driven Equal Channel
Angular Deformation Technology
Friction/Wear Behaviors of Magnetron Sputtered TiB2-C Composite Films on
Ti6Al4V Alloy Substrate
Research on Anti-Cracking Performance of Polypropylene Fiber Reinforced
Cement Mortar
Thermoelastic Contact Analysis of Functionally Graded Materials with
Properties Varying Exponentially
Research on Droplet Transfer of MIG Welding with Alternating Longitudinal
Magnetic Field
Kinematic Analysis and Optimization Design of an Eccentric Crank Slide-Block
Mechanism Based on ADAMS
Properties of Anodic Coatings Obtained in an Organic, Environmental
Electrolyte by Micro Arc Oxidation on Magnesium Alloy
Evaluation on Cleaning Effect of Cleaning Cloths for LCD Screen Using
Principal Component Analysis
Mechanical Properties of Flip-Chip Solder Joints Effected by
Electromigration
Explosive Compaction-Coating Manufacture Large Area Coat
Structure and Properties of Superfine Coating on Cast Steel by Electro-Spark
Deposition
Properties and Synthesis of -Fe2O3/SiO2 Composite Color
Thermal-Field Experimental Study of a Thin Circular Carbon-Fiber Tube in
Stratosphere Environment
Effects of Thermal Exposure on Mechanical Properties of Al-4.87Cu-1.2Mg-1.0Ag
Alloy
HRTEM Investigation of Precipitates in Al-Zn-In-Mg-Ti-Ce Anode Alloy
Improvement of Tribological Behavior of Biomedical Nanostructured Titanium by
Magnetron Sputtered SiC Films
Study and Application of Cemented Carbide Coating Technology
Synthesis, Characterization and Antimicrobial Activity of a New Preservative,
6-O-Chitosan Ester of P-Hydroxybenzoic Acid
Study on the Complex Strengthening Processes of 5Cr2NiMoVSi Steel Large Hot
Forging Dies
Numerical Research for the Film Surface Wave with the Different Flow Case
The Online Assessment Method of Tower Crane Effective Life Based on Tower
Crane Group Monitoring System
Friction and Wear Properties of W,Mo,Co Alloyed Layer on T8 Steel by
Double-Glow Technique
The Effect of Nano-TiO2 on the Performance of the Solar Heat-Reflective
Coating
Diffusion Study of Al-8%Si Alloy Double-Coating on Steel
Influence on Tribology Characteristic of the Steel-Cast Iron Friction Pair
under Different Concentration of the Self-Repairing Additive and Mechanism
Analyzing
Tribological Performance of TiAl Based Alloy Treated with Plasma Surface
Chromizing Process
The Influence of Plating Temperature on the Properties of Electroless Ni-Cu-P
Alloys on Aluminum
Photo-Aging of Polyurethane Coating Based on TDI-TMP and N3390
Properties of Ceramic Coatings on the Wall of Coke Oven
Different Curing Agents on the Photoaging of Polyurethane Coatings
Effect of Frequency on Composition and Microstructure of Siliconized Layer
Using Pulse Electrodeposition
Study on Characteristics of Acoustic Emission Property in the Normal Concrete
Fracture Test
Research on Random Stress Spectrum for Cumulative Fatigue of Crane Metal
Structure
Effect of Molecular Weight on Phase Diagram of Epoxy/Polyetherimide-Siloxane
Blends
Experimental Study on Mechanical Properties of Rubber Used for Damping
Bearing
Prediction of Ferrite Transformation in Nb-Containing Microalloyed Steels
during Continuous Cooling
Study on the Effect of Ultrasonic Waves on the Low Temperature Electroless
Ni-P Plating on Copper Substrate
Effect of Normalizing Pre-Treatment on Microstructure of Laser Hardened
Ductile Iron
Surface Treatment of Magnesia-Calcia Firebricks with CO2
Anticorrosive Films Prepared by Incorporating Permanganate Modified Carbon
Nanotubes into Waterborne Polyurethane Polymer
Experimental Study of Activation the Reactivity of Waste Mortar
Influence of Mn Doping on the Microstructure and Optical Properties of ZnS
Nanocrystals
Impact Abrasive Wear Resistance of High-Chromium Cast Iron Bars Reinforced
Hadfield Steel Matrix Composite
Study for Vibration Measurement and Failure Diagnostics System for CNC
Milling Machines Based on LabVIEW
Research on Optic Fiber Coatings and Curing Process Monitoring of Composites
Based on FBG
Fault Analysis on Crosshead Fracture of the Reciprocating Piston Compressor
C102B
Effects of Nd on Microstructure and Properties of Spray Deposited Mg-Al-Zn
Alloy
Research on Anti-Erosion Mechanical Properties of Steel Structure Coating
Enhanced Wear Resistance of Al-15Si and ZK60-1Y Mg Alloys Induced by High
Current Pulsed Electron Beam Treatment
Flame Retardant Polyamide 6 Composites Using NMH or NMH/MCA/APP
Effects of the Welding Process on Mechanical Properties and Corrosion
Resistance of 2205 Duplex Stainless Steel
Research on the Mathematical Model for the Price Regulation of Power
Demand-Side
Effect of Carbon Nanotubes Content on the Structure and Photo-Oxidation
Behaviors of Polypropylene
Effect of Preheating Temperature on the Cooling Curves of BW Quenching Media
Study of Stress in TiO2 Films Grown by Electron-Beam Evaporation
Modification of the Flax Fiber with Acetylation
Research on Mechanism of Polymer Inhibiting Secondary Reaction in Clinker
Leaching Process
Study on the Corrosion Resistance and Wear Resistance of Micro-Arc Oxidation
Coatings on the Clad Plate of Aluminum and Magnesium Alloy
Calibration Methods of an On-Line Inspection System on a Large-Scale
Turning-Milling Machining Center
Influence of Annealing Temperature on the Antibacterial Activities and
Photoactivity of N-Doped TiO2 Films by Ion Beam Assistance
A Kind of Non-Contact Measurement System for Areal Surface Texture
Study on the Brush Plating Technology of GH34 Heat-Resisting Steels
Evolution of Crystalline Phase and Morphology of the Products Formed during
the Hydrothermal Synthesis of Y2O3 Powders
Study on Micro-Arc Oxidation Composite Ceramic Coating Properties in the
Textile Machinery Spare Parts
The Corrosion Mechanism of Zn-5%Al-0.3%Mg Coating
Comparative Study of Friction and Wear Behavior of Diamond-Like Carbon
Coating under Various Lubricants
Process, Microstructure and Properties of Plasma-Sprayed Ceramic Coating on
AZ91D Magnesium Alloy
Design of Scanning Micro-Arc Oxidation Forming Ceramic Coatings on 2024
Aluminium Alloy
Research on Surface Metallization of Carbon Fiber Based on Electroless
Plating
The Design of CNC System on the Electron Beam Welder
Tribology of Plasma Sprayed Al2O3-13%TiO2 on AZ91D Magnesium Alloy
Study on Electron Beam Alloying Micro-Structure and Wear Performance of
3Cr2W8V
Studies on Mechanical Properties of Thin-Walled MHS Structure
Study on the Prediction of Surface Roughness of ZTA Ceramics under Ultrasonic
Assisted Grinding
Study on Milling Gray Cast Iron Using PCBN Indexable Face Milling Tools
Experimental Research on the Sound Insulation Property of Lightweight
Composite Paper Honeycomb Core Wallboard
Preparation and Electrical Properties of Aligned Carbon Nanotubes/Epoxy Resin
Composites Induced by a Low Magnetic Field
Preparation of Wood-Based EMI Shielding Composite via a Short Process
Electroless Plating
Stochastic Finite Element Method for Nonlinear Dynamic Problem with Random
Parameters
Research on Fault Diagnosis and Application for Rolling Element Bearing Based
on Fuzzy Analysis
Preparation of the Layer-by-Layer Deposited Silver Nanoparticles Multilayer
Films on Poly(ethylene Terephalate) Substrate
High Stable Mechanism Design for Micro-Wire Transport System in WEDM
Research on the Temperature Field and Roast Mechanism of Blast Furnace
Tap-Hole Clay
Surface Roughness Prediction in End Milling of Machinable Glass Ceramic and
Optimization by Response Surface Methodology
Observation of Capillaries after Implanting Porous Silk Fibroin Films in
Rats
Microstructure and Creep Properties of Casting Mg-8Al-0.3Mn Alloy Containing
Ca and Sr
Optimization of Process Parameters on Ti-6Al-4V Using Central Composite
Design Method
Press Forging of Thin-Walled AZ31 Magnesium-Alloy Components
2 Modeling, Analysis and Simulation
Topological Synthesis of Fully Decoupled Parallel Manipulators by Screw
Formulation of Jacobian Matrix
RDX Kinetic Model Evaluation by Nth Order Kinetic Algorithms and Model
Simulations
Thermal Stability Determination, Anti-Biodegradation, and Thermal Degradation
of Nitrocellulose with Various Nitrogen Content by DSC and FT-IR
Phase-Field Simulation of Double Dendritic Growth in Solidification of Binary
Alloy with Forced Convection
The Wavelet Analysis and Processing of Weak Vibration Signal
Preparation and Stress Calculation Analysis of Light Elastic-Plastic
Material
Finite Element Simulation of Residual Stress in Heavy Rail
The Determination of Using Limiting Clearance between Crank Pin and Bearing
Bush in Volkswagen
Direct Electro-Magnetic Mechanical Analysis of U-Shape Coil
Numerical Analysis of Micro-Mixing in Rough Microchannels
Study on Hot Deformation Behavior and Processing Maps of Cu-0.35Cr-0.15Zr
Alloy
Influence of Parameter Identification of Anisotropic Yield Function on
Spring-Back Prediction in Finite Element Simulation of Sheet Metal Forming
Process
Structural Optimization of Ground Vias for 3D ICs
The Numerical Simulation of Directional Solidification Process Temperature
Field for Large-Scale Frustum of a Cone Ingot
SVR-Based Predictive Model for Purity of the Mg-Al-Hydrotalcite
Optimal Design of Automotive Steering Column Bearing by Simulated Annealing
Algorithm
Numerical Study of Defect Free Elbows Subjected to In-Plane Bending Moment
Design Thermal Structure of Aluminum Plate LED
Temperature Rise and Heat Transfer in High Speed Machining: FEM Modeling and
Experimental Validation
Determination of Mechanical Behavior of AA5083 Alloy under Machining
Conditions, Applicable in Metal Cutting Simulation
Fatigue Reliability Analysis of Pressure-Reducing Valve
Numerical Simulation of Intermediate Frequency Induced Heating Steel Plate
with Finite Element Method
Study of Contact Temperature in Polishing Surfaces
Impact of Float Loss on the Project Costs
Effect of Surface Roughness on Slip Resistance of Rubber
A Novel Ultrasonic Motor Driver Based on Two Phase PWM Signals
Prediction of Processing Parameters of Laser Clad TiC/NiCrBSiC Coatings on
Ti6Al4V by Finite Element Analysis
3D FEM Modeling of Ball End Milling of HSM H13 Die Steel with Cutter
Inclination
The Deformation Analysis for Flank Milling of Thin-Walled Rectangle Plate
Based on Flexible Force Model
An Hybrid Expert Fault Diagnosis System for CNC System
The Parametric Design of the External Transmission of Involute Beveloid Gear
with Parallel Axes
Virtual Measurement of Machining Errors Based on Comparison Method of Three
Models
Head Surface Reconstruction and Correction of Reverse Engineering Based on
CATIA's
Finite Cylindrical Shell Element Method which Analyses Local Stability of
Buried Stiffened-Penstock
Bio-Oil Production from Agricultural Residues in Northeast of Thailand by
Fast Pyrolysis Technology
Research on Complex Product Design Method Based on Knowledge Model-Driven
The Control and Dynamical Analysis on Magnetic Bearing Flexible Rotor System
Combining the Whirling with Swing
Application of Virtual Design and Manufacturing Techniques in Large Mine
Elevator
Simulation and Design for Laser Protective Structures of Aluminum Material
Numerical Modeling of the Thermal Performance of 3D SiP with TSV
Numerical Analysis of Thermally-Induced Residual Stresses in Plasma Facing
Components for Fusion Reactor
Research on Influence of Longitudinal Gradient to Rigid Base Composite Road
of Cross River (Sea) Tunnel under Large Longitudinal Slope
A Multiple View Assembly Process Representation Based on Three Dimensional
Models
Water Vapor Cooling Effects in Turning by Finite Element Modeling
Piston Stroke Design Optimization for Linear Compressor
Radiative Transfer Modeling and Monte Carlo Simulating of a New Digital
Airborne Camera
Study on Friction Wear Properties of Vanadium-Chromium Surface Composite
Layer under Dry Sliding Condition
Analytically Study the Ferrohydrostatic Pressure with FHD Bernoulli Theory
CFD-Based Multicomponent Model for Solidification of Casting Process
Theoretical Study of the Effect of (F, Li) Codoping on P-Type Tendency in
ZnO
Transient Heat Conduction in Functionally Graded Materials by LT-MFS
The Thermal-Mechanical Coupled FEM Analysis on 3-Roll Continual Tube Rolling
PQF Deformation Process
Influence of Process Parameters on Plastic Injection Molding of Automobile
Interior Trim
An Image-Based Microscale Simulation of Thermal Residual Stresses in DSE
Oxide Ceramic Composite
Study on the Vertical Extrusion Process of Ultra-Thick Seamless Steel Pipe
Numerical Analysis and Experimental Study on Dipper Handle of W1002
Excavator
Analysis about Vibration and Noise of Ceramic Electrical Spindle
Research on the New Compound Technology of Integral Seamless Housing of Rear
Axle
Simulating Design of Magnetic Fluids Lubricating Unit Structure with Porous
Material
Simulation on Pipe Joints Expansion Technology of NiTiNb Shape Memory Alloy
Finite Element Analysis for the Wind Resistance of the Tower of Wind Turbine
Study on Process Concentrating of a Certain Limonite Ore in Xinjiang
Modeling of Anchors in Gravel Formation Using Discrete Element Method
High Air Pressure in MQL Deep Hole Drilling Workpiece Temperature
Modelling the Grain Pattern and Orientation in Radiata Pine Boards
Modelling Knot Architecture in Radiata Pine Logs and Boards
On Resistance Calculation for Autonomous Underwater Vehicles
Modeling of Aluminum Extrusion Process Using Non-Orthogonal Block Structured
Grids Based FVM
Effect of Rare Earth on Microstructure and Impact Toughness of Low Carbon
Steel Based on Compact Strip Production Process
Effects of Heating Vents in a Tunnel-Type Dryer
The Effects of ZigBee Position with Different Hidden Layers in
Back-Propagation Neural Network
Surface Grinding Force Model of Steel 55 Based on Undeformed Chip Thickness
with CBN Electroplated Wheels
Spatial Cam Modeling and Analysis on Curvature of Conjugated Surfaces
Influence of Heating Models on Necking Deformation during Tube Extrusion
Process
Experiment and Numerical Study of Annular Flow Entrainment Mechanism in
Oil-Air Lubrication Pipe
Modeling and Analysis of Soft Contact in Robotic Grasping Using Bond Graph
Methods
Dynamic Contact Analysis of the Offset Face Gear
Mechanical Properties of Commercially Pure Titanium during Hot Compression
The Wave-Load Analysis of the Offshore Wind Power Installation Vessel Based
on Frequency-Domain Methods
Study on Controlled Release Properties of Slow-Release Pellets
Study on Angular Stiffness of Monolithic Flexible Joint
Analysis of Mechanical Properties of Pipes with Helical Reinforcement under
Axial Tension
Application of the Arbitrary Lagrangian Eulerian Formalism to Stationary Roll
Forming Simulations
Study on the Distribution Law of the Crashed Coal Fragmentation
Numerical Analysis on Impact Load of Elasto-Plastic Spherical Impact
Anslysis of the 5-m Heavy Plate Mill Stand Based on MSC.Marc Finite Element
Method
Temperature Simulation in High-Speed Grinding by Using Deform-3D
Application of Support Vector Machine to Predicting Mechanical Properties of
TC4
The Research on Friction Impacting on Drawing High-Strength Steel
Laser Anneal-Induced Effects on the NBTI Degradation of Advanced-Process 45nm
High-K PMOS
Research on Performance Characteristic of Novel Fomichev Plug Used in
Julong-Type Piercer
Study on the Burning Characteristics of Poor-Quality Anthracite in
Supercritical W-Shaped Flame Boiler
Optimization Technique for Neural Network-Based Error Compensation in CNC
Machining
Virtual Prototype Design and Dynamic Simulation of High-Dump Truck Based on
ADAMS
Corrected Diffusion Model of Chloride in Concrete and its Engineering
Application
The Thermal Response Investigation of Functionally Graded Material Plates
Coupled-Field Analysis of the Compliant Slider Mechanism with Rectangle
Flexure Hinges Based on ANSYS
Influence of Guide Disc Postposition on Rolling Process of Accu-Roll Mill
Finite Element Analysis of RPC-Filled Steel Tube Stub Columns
Fatigue Analysis of Planet Carrier Based on Collaborative Simulation
Power Flow and Energy Sharing between an Oscillator and a Continuous Receiver
Structure
Wear Mechanisms Approach to Ni-P Electroless Plating Applied to Hardening
Engine Cylinder
Numerical Simulation of Different Clamping Modes on Stretch Forming Parts
3D Finite Element Modeling of the Machining of Ti6Al4V Alloys
Identification Algorithm for Instantaneous Engaged Cutting Edge Elements in
Five-Axis Milling
Study on Metal Flow in Continuous Extrusion Cladding of Cable Aluminum Sheath
Using FEM Analysis
Numerical Simulation of Polymer Flows in Coat-Hanger Die Using Wagner
Constitutive Model
Numerical Simulation of Effect of Slip Conditions on PVC Co-Rotating
Twin-Screw Extrusion
Mathematical Modeling and Modifying of Turntables Angle for 5/12 Automatic
Numerical Controlling Bending Hoop Machine
Research on the Stress and Strain Field and Wall Thickness in Power Spinning
of Ellipsoidal Heads with Variable Thickness
Contact Deformation and Abrasion Analysis of the Contact Region for Roller
Linear Guide
Research of New Type PAN-Based Carbon Fiber Pre-Oxidization Furnace and its
Temperature Controlling Property
Application of Digital Close Range Photogrammetry in Mechanical
Three-Dimensional Modeling
Analysis on Combination of Different Wavelengths in Surface Roughness
Measurement by Polychromatic Laser Speckle Patterns
Optimum Design Study of a Hydraulic Pressure Derrick Based on Stability
Temperature Field Modeling and Thermal Deformation Analysis of Turning and
Milling Machining Center
3D FE Modeling of Three Rolls Cross Rolling Process of a Rotary Disk Part
Numerical Simulation of Flow Field in Cavitations-Impinging Stream Reactor
Simulation of Reflective Crack Propagation Path in Asphalt Overlay under the
Partial Wheel Load
Temperature Stress Field Distribution Study of Asphalt CarrierS Based on
Rockwool Damaged
Numerical Analysis and Experimental Study on Temperature Field of Brake Disc
during the Air-Cooling Process
A Numerical Study on the Uplift Behavior of Under-Reamed Anchors in Silty
Sand
Modeling and Simulation of Gear Transmission System of Drive Axle with Romax
Design and Analyses of Roof Structure in Hangzhou Grand Theater
The Simulation of Polycrystalline Silicon Thin Film Deposition in PECVD
System
New Geometry of Face-Gear with Curvilinear Shaped Teeth and Non-Zero Spiral
Angle: Machining Mathematical Model Analysis and Simulation
Improving Pattern Recognition Rate by Gaussian Hopfield Neural Network
Calculation and Analysis on the Key Parameters of High-Speed Linear Motor
Feed System
Optimization Design of Ride Comfort for Wind Blade Transporter
Numerical Analysis of Coupled Finite Element with Meshfree in Bulging Process
of Sheet Elastic Flexible-Die Forming
Study on Thermal Stresses of Cylinder Liners Fabrication Using FEM Analysis
Space Robot Self-Assembling Dynamics and Control
Modal Analysis of Self-Repairing Composite Gear Based on ANSYS
Computer Simulation of Fracture Damage for Large-Diameter Percussive Drill
Residual Stresses Distribution Calculation of the Cu-Cr-Zr Alloy Contact Wire
Used in High-Speed Electrical Railway
Minimizing the Warpage and Sink Mark Depth in Injection-Molded
Thermoplastics
Numerical Study on the Large Deformation of Silicone Rubber Foams Based on
Random Cell Models
Axial Spread Evolution during Hot Rolling of Large Rings with Different
Sizes
The Numerical Simulation about Second Dendrite Spacing of Low Pressure
Casting Automobile Aluminum Magnesium Alloy Wheel
Nonlinear Fitting Technology of 7-Parameter Cross-WLF Viscosity Model
Analysis for Effect of Key Parts on Precision of High Precision Machine
Center
Study on Ultrasonic Surface Rolling Process Using FEM Analysis
Optimal Clamping Scheme of Thin-Walled Cavity Workpiece
Integrated Simulation of Injection Molding Process and Mold Deformation Using
the Uniform Mesh
Solder Joints Reliability Assessment for Stacked CSP Module Based on Flexible
Circuit Printed Board
The Overview of Modeling the Thermo-Mechanical Three Dimensional Friction
Stir Welding Process
Mechanism Analysis of Magnetostrictive Turning for Piston Skirt Processing
Modeling of Pillowing Stress in Corroded Lap Joints
Investigation on the Numerical Simulation of Hot Stamping of Advanced High
Strength Steels
Advanced Interactive Device in Virtual Knee Arthroscopic Surgery
Optimization Research on Workpiece Clamping Deformation Using Genetic
Algorithm and Finite Element Method
Finite Element Analysis on Contact of Wheel and High Manganese Steel
Crossing
Research on Rapid Prototyping Machine of Ceramic Parts and the Machine
Control System
Design of New Hydraulic Lifts for Construction Machinery Assembly
3D Finite Element Modeling for Particle-Reinforced Polymer Composites for
Wind Energy Application
The Numerical Simulation of the Water Jet in Hydroentanglement
Study on Electrical Resistance Tomography Simulation of Carbon Fiber Smart
Layers on Two-Dimensional Curved Surface
Discrete Jerk-Limited Feedrate Planning for NURBS Curves Interpolation
Numerical Simulation Analysis of Deformation in TIG Welding of I-Steel
Cellular Automata Simulation of Grain Growth under Consideration of Zener
Pinning
Expansion Order Effect on Residual Contact Pressure of Tube to Tubesheet
Joint by Hydraulic Expansion
The Estimation of TP Chromatic Aberration by Using Neural Network
Analysis on Internal Gear Stress for Design Parameters
Virtual Simulation of Embedded-Vane Rotary Compressor
CAD Design and Mechanical Test on inside Porous Parts
Numerical Simulation of Plate Bender Bending Process
The Static and Dynamic Characteristics Study of Aluminum Tank Semitrailer
Research on Thermal Error Modeling and Simulation Technique of CNC Based on
Stepped Approximation Method
The Definition and Solution to the Correlation in District Collaborative
Design
Discussion on Convergence Issues in ABAQUS/Standard while Carrying Out Damage
and Fracture Analysis
Study on the Effects of the Geometrical Parameter of Twist Drill on the
Drilling Performance of Stainless Steel
Flow of Finite Element Analysis of Metal Powder in Medal Injection Mold
Runner
Three-Dimensional Finite Element Analysis in Cutting Temperature for High
Speed Milling of Titanium Alloys
Research on Dynamic Fatigue Strength Criterion of BTA Deep Hole Boring Bar
for Consideration Vortex Surrounded by Internal and External Cutting Fluid
Study on Thermal Placement Optimization of Embedded MCM
Determination of Flow Stress Based on Cutting Simulation and Optimization
Study on the Mechanism of the Impactor-Bit-Rock Interaction Using 3D FEM
Analysis
Flow Features Analysis of Throttle Notches of Proportional Direct Valve
Dependence of Structural Stress on Indium Bump Sizes in 8×8 InSb Focal Plane
Array
A Method of the Inverse Evaluation for Heat Transfer Coefficient between
Al-Cu Alloys and Cooling Water
Simulation of Multiscale Time and Space in Fracture Process of
Three-Point-Bending Concrete Beam with Offset Notch
Debonding Analysis between FRP-Concrete Interface with a Linear Elastic
Fracture Mechanics Approach
Error Analysis of Ladder Shaft Turning and the Research of NC Compensation
Study of Precision Formation on New Synchronizing Ring of Heavy-Duty Truck
Based on Computer Numerical Simulation
Numerical Simulation Analysis of Spinning Forming Process of Tubeless Steel
Wheel on Technical Parameters
Numerical Optimization Design on the Parameters of Double Ellipsoid Welding
Heat Source
Limit Bearing Capacity Analysis of Structure System with Different Types of
Element Using Elastic Modulus Reduction Method
Research on Classification Method of Multi-Circuit Pump Critical Parts Based
on Fuzzy Theory
Experimental Analysis and Performance Evaluation of Fu Feng Highway
Prestressed Concrete Bridge after Strengthening in China
Theoretical Analysis of Designed Internal Forces of Jiamusi Highway
Prestressed Concrete Bridge before Strengthening in China
Numerical Simulation of the Viscous Flow for the Supersonic Jet Element
Calculation of Static Safety Coefficient about Loess Cave
Optimal Design of Plastic Injection Mould Gating System
Analysis of Metal Flow and Deformation Features during Continuous Tube
Rolling Process with Mandrel Mill
Influence of Wall Thickness Fluctuation of Pierced Shell on Continuous Tube
Rolling Process of Semi-Floating Mandrel Mill
Elastic-Plasticity Analyze of Bending Deflection on Profiled Bar Roller
Straightening
Multi-Dimensional Numerical Simulation of Emission Characteristics in DI
Diesel Engine
Numeral Simulation of a New Forming Process: Stretch Forming Combined with
Roll Forming
The Study of the Model for the Formation Process of GMAW
Influence of Turbulence Controller on Flow Mode of Molten Steel in Tundish
Study on Creep Deformation of Reactor Coolant Pump Rotor-Can during Vacuum
Hot Bulge Forming Process
Imitative Farmland Random Vibration Analysis on Frame of Blueberry
Harvesters
Numerical Modelling of Shape Evolution of Tubular Preform in Spray Forming
Process
Research on the Application of Expansion Ratio Analysis for Die-Face Optimal
Design in Sheet Metal Forming
3 Materials Forming
Mechanism for In Situ Iron Nanoparticles Formed during Copper Alloy
Solidification
The Synthesis of Mg-Zn-Al LDH and the Sustained-Release Properties of
Theophylline Intercalated LDH
Investigation of Coupling Efficiency by Plastic Deformation of Tube Packaging
for Thin-Film-Based Passive Optical Components
Microstructures Development in Al-5Fe and Al-5Fe-3Y Alloys Solidified at
Different Cooling Rate
Virtual Disassembly Simulation of Varying Target Component for Complex
Products
Explosive Compaction of Metallic Glass Particles Reinforced Aluminium Matrix
Composites
Investigation of Mold Temperature Affecting on Shrinkage of Rapid Heat Cycle
Molding Plastic Part
Design Milling Parameters Optimization System Based on Thin-Walled Parts
Study on Machinability and Polishing Performance of 1CrMn2MoVTiB Non-Quenched
and Tempered Plastic Mould Steel
Analysis for Fracture Behavior of Compactor Grinding Tooth Forging Die Based
on Finite Element Method
Influence of Segmented Blank Holder for Rectangular Box Drawing
Consolidation of HLW into Mineral-Like Materials by the SHS
Superplasticity-Like Behavior, Microstructures and Deformation Mechanism Map
in Superlight Mg-6Li-3Zn Alloy
An Upper-Bound Analysis of Closed Multi-Ram Forging of Rod
Application of Advanced Cooling Control System for Plate Mill
Research on Flow Stress of Magnesium Alloy Sheet under Warm and High Strain
Rate Forming Condition
Injection Mould Parametric Reusable 3D Parts Libraries of Development
Maintenance Process Simulation Model Considered Sharing Resource and its
Application
Numerical Simulation on Thixo-Forging of Magnesium Matrix Composite
Numerical Simulation and Experimental Study of Limit Drawing Ratio of Steel
Sheets
Survey and Trend of Rapid Heat Cycle Molding
Effect of Position between Upper Die and Workpiece on Cold Rotary Forging
Optimal Design of the Guide Mechanism of Vertical Ring Rolling Mill
Influence of Cross Section Shapes of Preformed Blade Body for Final Forging
Formability Based on Numerical Simulation
The Model of Thermal Deformation Resistance for P20 Steel
Analysis and Control of Car Door Inner Panel Forming Fracture Based on
Experience Knowledge and Numerical Simulation
PSO Algorithm Based Task Allocation in Dynamic Virtual Enterprise
Research on Workshop Scheduling of SMT Product Manufacturing System
Development of an Indirect Solid Freeform Fabrication Process Based on
Stereolithography and Gelcasting for Ceramic Casting Molds
Effect of Drive Roll Rotation Speed on Ring Rolling Process
Stray Light Elimination Methods for Laser Communication System with
Submarine
COF Measurement of Tubes by Hydraulic Bulging with Radial Crushing
Test and Analysis of Friction Torque for Wind Turbine Pitch Bearing
Numerical Simulation of Microstructure Evolution of Hot Forging
Microstructure of AZ31 Magnesium Alloy Produced by the CONFORM Process under
Different Extrusion Wheel Velocities
The Mechanism and Influence Factors of Struvite Precipitation for the Removal
of Ammonium Nitrogen
Real-Time Data-Based Fault Diagnosis System
Study of Solutions and Causes for Scrap Jumping up in High-Speed Stamping
Diagnosis System of Manufacturing Equipment Based on Structure-Fault Tree
Finite Element Simulation and Experimental Study of the Effect of Cone
Parameter on Thickness Distribution in Hydroforming of Conical-Cylindrical
Cups
Test Research of Stamping Property for 500MPa Grade Super Steel Sheet
Study on the Large Module Spur Gear Cold Forming Process by Means of
Numerical Simulation
Punch Die of 385 Diesel Part Design Based on CAE Technology
Blank Thickness Effects on Rolling Force in Hot Rolling of Titanium Alloy
Large Rings
Finite Element Analysis of Bulging Forming for Sheet Metal with Bottom
Compression Drawing Method
The Decomposition Mechanism of Titania Film with Nanotube Structure
A Fault Diagnosis of Suck Rod Pumping System Based on Wavelet Packet and RBF
Network
Thickness Indirect Measurement Method for Direct Pulling Pilot Cold Rolling
Mill
The Investigation of Multi-Stage Sheet Metal Stamping Process for Deep
Drawing
Study on Regulation of Rotation Speeds and Tangent Slip in Radial-Axial Ring
Rolling Process
A New Axial Upsetting Process for Large Ingots with Large Ratio of Height to
Diameter
Influences of Material Thickness on Hole-Flange Forming Limitation
Preparation and Characteristics of Expanded Graphite
Function Analysis of Injection Molding
Analysis of Draw Bead Geometry on Wall Thinning and Concave/Convex Feature in
Rectangular Deep Drawn Parts
Microstructure and IR Studies of Ag Ions-Zeolite
Design of Drawing Compound Die for Side Hole Part
Research of Numerical Simulation Method in Two Pass Deep Drawing Forming of
Sheet Metal
Predict and Analysis of Fold in Steering Knuckle Forging Based on Numerical
Simulation
Design and Realization of Automatic Testing System for Hydraulic Pump
Novel Carbon Source in Manufacture of LiFePO4/C
Analysis and Study of Damage of Forging Cracks
Research on Ball Spinning Forming of Superalloy Inconel 718 Thin-Walled Tube
A New Hybrid Particle Swarm Optimization for Solving Flow Shop Scheduling
Problem with Fuzzy due Date
Processing Parameters Optimization for Stagger Spinning of Trapezoidal Inner
Gear
An Artificial Immune Algorithm Based Intelligent Monitoring System in
Grinding Process
A New Flaw Identification Model of Ultrasonic Signals Based on EMD and
Possibility SVM
Numerical Simulation and Process Optimization for Multi-Stage Forming of
Wheel Centre Disc
Warm Compacting Behavior of Pure Titanium Powders
Research on Warm-Cold Precision Forging Process and Numerical Simulation for
Spherical Housing
Effect of Geometry Parameters on Cross-Sectional Distortion of Thin-Walled
Rectangular Tube in Rotary-Draw Bending Process
The Study of Parameters on CK67 Steel Sheet Spring-Back in L-Dies Bending
Processes
A Single Stage Hot Forging Process of Alternator Poles
Effects of Preform on Thickness Distribution of Hydroformed Y-Shaped Tube
An On-Line Multiparametric Water Quality Monitoring System Based on Visible
Spectrophotometry
Finite Element Analysis for the Influence of the Clamping Holder Corner on
the Bulging of Thin Metal Shells
LY11 Alloy Flat Bar Produced by Continuous Semisolid Extruding Extending
Forming Process
Control on Head Displacement of H-Beam in Rolling Process
The Experimental Study on the Microstructure of SS400 Steel with Traveling
Magnetic Induced Rapid Tempering Process
Grain Refinement in Constrained Groove Pressing of 7050 Aluminum Alloy
Effect of Magnetic Field on Air Film Continuous Casting
Study on Cold Extrusion Process and Die for Vehicle Sleeve Gear with Spline
Effect of Severe Plastic Deformation on the Characteristics of a PM Aluminum
Alloy
The System Design of Spiral Drum Based on Parameterized Modules
A Study on Dynamic Recrystallization Behaviours of AZ80 Magnesium Alloy
Blank Optimization of Sheet Metal Forming Based on Response Surface
Methodology
Embedded Web-Based Remote Monitoring System of the Motor
Study on Metallography and Properties of WC Cast-Infiltration on Carbon Steel
Surface by Expendable Pattern Casting
An Investigation on Effect of Residual Stress on Springback Behavior of High
Strength Steel in U-Bending Process
Effect of Rare Earth (RE) La on Solid Solution of Second Phase Particle and
Austenite Grain Growth in Steel Containing High Niobium
Research on a Compiler for NC System Based on PC
The Analysis of Core Shift in Injection Mold and its Optimization Based on
AMI
Thickness Distribution in Conical Parts Formed by Hydroforming and
Conventional Multistage Deep Drawing Processes
Investigation on the Elongation of Tailor Welded Blanks with Different
Thickness
Numerical Simulation of Deep-Drawing Processes of Square Cup under Bilateral
Constrained Conditions
The Effect of Purity of Zirconium Material on Mechanical Properties and
Microstructure of Zr-Based Bulk Metallic Glass
Experimental Study of Hot Extrusion Micro Gear of Brass H62
CAD Software Development for the Continuous Flexible Forming Process
Numerical Simulation and Verification of Multi-Operation Sheet Forming
Process for Stamping Parts of Spiral Step Surface
Co-Deposition of Binary Particles during Slip Casting Process
Effects of Continuous Extrusion on Microstructure Evolution and Property
Characteristics of Brass Alloy
Consititutive Modeling for Auto-Body Steel Sheet Incorporating Strain Rate
and Temperature
The Desing and Research of the Interior Sprue Gate of Die-Casting Mould
Study on Direct Hot Isostatic Pressing Technology for Superalloy Inconel 625
Effect of Molding Parameters on the Interface Morphology of Metal
Co-Injection Molding
Fabrication and Bending Strength of Al/SiC Composites with High Volume
Fraction of Reinforcement by Combining Powder Injection Molding and Pressure
Infiltration
Development of Experimental Method to Improve Sheet Metal Formability by
Transverse Normal Stress
Study on Springback Compensation in Multi-Point Forming
A New Type Multi-Mode Linear Ultrasonic Motor
Effect of the Thickness Ratio on the Failure Modes of Tailor Welded Blanks
Study on the Metal Flow in Power Spinning Process of Parts with Transverse
Inner Rib
Thickness Demarcation Circle of Double-Cone Tube during Hydroforming
Analysis of Strip Shape in Cold Rolling of Thin Strip
Cell Direct Assembly Technology Adopting Hybrid of Gelatin-Based Hydrogels
Numerical Simulation on Efficient Spinning Technology Based on Multi-Point
Adjusting Principle
Determination of Optimal Microminiature Powder Injection Molding Parameters
by Taguchi Approach
Investigation of High Strength Steel for Automotive Roll-Forming Parts
Influence of Operation Conditions and Ambient Temperature on Performance of
Gas Turbine Power Plant
4 Materials Machining
The Research of a Drill Bit for Underground Casing Drilling in Radial Water
Jet Penetration Perforation
Investigation of Airflow Field in Grinding Zone Based on FLUENT
Experimental Research on the Dry Electrostatic Cooling Assisted Machining for
Hardened Steel
Drawing Properties of Modified Polyamide 6 Fibers
Contrast Studies on the Solar Drying Schemes of Eucalypt Timber
Tool-Path Generation for Conical Groove of Cylindrical Cams by Small-Sized
Cutting Tools
Tool Path Design Methods for High Efficiency Die Cavity Machining with
CAD/CAM Technology
Application of Taguchi Method in the Optimization of Cutting Parameters for
Turning Metal Matrix Composite
Experimental Study and Theory Prediction on Adiabatic Shear Critical
Conditions of Hardened AISI 1045 Steel
Cutting Test and Analysis of the Emulsified Deep-Hole Cutting Fluid
MQL Technology Including the BTA Deep Hole Drilling Machining
The Effect of Two-Step Aging on the Electrical Properties of 7075 Aluminum
Alloy
Comparative Study on Force in Milling T10 Hardened Steel with Different
Machining Parameters
Influence on Cutting Forces and Vibration in High Speed Machining Pocket
Corner
The Experiment Research of High-Pressured Cauldrons Anti-Hydration
Study on Decreasing Processing Cost of Special-Shaped End Socket
Nano-Process of SiC Ceramics by Molecular Simulation
An Ultrasonic Elliptical Vibration Burnishing Process for Reducing Surface
Roughness
Error Analysis and Simulation of Gear Form Grinding
Application and Development of High-Efficiency Abrasive Finishing
A Modified Isoscallop Height Toolpath Planning Method for Generating Smooth
Paths Based on Curve Fitting Method
Machining Characteristics of EDM Using Gas Media
A New Effective Hybrid Optimization Strategy for Rectangular Packing Problem
Cutting Temperature and Tool Wear in Internal Spray-Cooling Vibration
Drilling of Superalloys
Study of High-Speed Machining Parameters on Nickel-Based Alloy GH2132
The Analysis of High-Speed Shearing Mechanic and Cross-Section about Sheet
Metal
Effect of the Surfactant Concentration on Sinking Electric Discharge
Machining Performance with Water-in-Oil Emulsion as Dielectric
Study on the Deep-Hole Honing of Cavity of Oxygen-Free Copper
Research on Higher Frequency, Short Pulses and Assisted Magnetic Field
Electrochemical Machining
Optimization for Tooth Profile of Assembled Cathode Based on Comsol
Development of Cutting Tools with Built-in Thin Film Thermocouple for
Monitoring Machining Temperature
Research on Several Machining Processes of the up-down Abnormity Hole by
WEDM
Electrochemical Micro-Drilling with Ultra-Short Pulses
Experimental Study of the Critical Process Parameters of Machining of
Stainless Steels Using the Taguchi Approach
Experiment Study of Oil-Air Lubrication on Cooling of Turning Tools
Grinding Performance of Porous Diamond Wheels on Different Materials
Research on the Vibration Tapping Performance of Particle Reinforced Aluminum
Matrix Composites
Study on Cutting Process of Manual SHS Cutting Technology
Wear of Uncoated HSS Tools in Drilling Difficult-to-Machine Materials with
Water Vapor as Coolant and Lubricant
Study on the Size Shrinking and Shape Changing of Solid-State Nanopores
5 Welding & Joining
Ice Accretion of Glaze Loads Model on Wires of Power Transmission Lines
Study of Flux on Wetting Behavior of Sn-Zn Lead-Free Solders
Ice Accretion Cause and Mechanism of Glaze on Wires of Power Transmission
Lines
Acoustic Signal Recognition Based on Time Series Model
Diffusion Bonding of ZrB2 Ceramic and Al-Sn-Mg Alloys at Atmosphere
Microstructure and Mechanical Properties of Aluminum/Stainless Steel Joints
Welded by Different Weld Heat Input
Study on Intelligent Analysis of the Causes of SMT Solder Joint Defects Based
on Fuzzy Neural Network
ICAI Realization Method for Parallel Robot Instruction
Influence of Friction Stir Welding Process on the Weld Formation and Tensile
Strength of Titanium and Aluminum Dissimilar Alloys Welded Joint
Analysis of the Hardness and Elastic Modulus Distribution in a High Strength
Steel Welded Joint by Nanoindentation
The Thinking of Using Multimedia Technology to Improve the Quality of
Mathematics Teaching
Enhancement of Load-Carrying Capacity of Undermatching Butt Joints by Weld
Shape Design
Innovation for Joining by Forming of Magnesium Alloy Based on TRIZ
Application and Research on Corrosion and Scale Inhibitor WJF-6 in Seawater
Circulation Cooling Water
Research and Prospects of Improving the Fatigue Life of Wleded Train Bogie
Structure
Research about the Effect of Ultrasonic Impact on the Fatigue Life of Butt
Weld Joint of 16MnR Steel
Study on Nonlinear Multiple Regression Modeling of Nugget Morphology for
Unequal-Thickness Dissimilar Steel Welding
The Effect of Carbon Content in Filling Alloys on Phase Formation in the
Interface Zone of YG30 and Weld Bead
Inverse Analysis of Material Parameters of Multiple Foam Layers Based on
Artificial Neural Network
Simulation on the Thermal Behavior in Vacuum Electron Beam Welding of
Magnesium Alloy
Microstructure and Mechanical Property of (Sn-9Zn0.05Ce)xBi Solder
Monitoring of Effect of Electrode Force on Resistance Spot Weld Quality Using
Electrode Displacement Method
Study on the Microstructure and Properties of Zl114a Friction Stir Welded
Joint with Forced Cooling
Microstructural Characterizations of the 316 Stainless Steel-Alumina Joining
by a Modified Moly-Manganese Process and Brazing
Effect of Cooling Condition on Microstructure and Mechanical Properties in
Large Line Energy Welded Joints of Ultra-Fine Grained Steel
Numerical Analysis of Controlling Welding Deformation of the Wall Plate of
Large Cylindrical Structure by Pre-Stress Method
Welded Joint Nonpenetration and Slag Inclusion Evaluation Based on MMM Signal
Characteristic
Effect of Electrode Force Change on Spot Weld Quality of AHSS Using Servo
Gun
Quality Estimation of the Resistance Spot Welding Based on Hopfield Network
Research of Surfacing Technology on Continuous Casting Roller
Effect of Welding Heat Circulation on the Microstructure and Mechanical
Properties of 500MPa Ultra Fine Grained Steel in HAZ
Formation and Growth of Intermetallic Compound Layers at Interface of
Solder/Copper Alloys for Lead Frame
Quasi-Static Analysis of Beam Described by Fractional Derivative Kelvin
Viscoelastic Model under Lateral Load
Effects of Wire Rotating Frequency on Metal Transfer Process in Rotating Arc
Narrow Gap Horizontal GMAW
Microstructures and Properties of Thick Plate Butt Joints of Al Alloy 6082
Prepared with FSW
Review of Dynamic Reliability Analysis on Wind Turbine
Research of Material Flow for Friction Stir Welding Using Smooth Pins Based
on Plasticine Analog
Study on the Legs Connection Technology of Jack-up Drilling Platform
The Structure and Mechanical Properties of Turtle Shell and Biomimetic
Numerical Simulation of Punching Bonding Based on AutoForm
Stress Distribution of Bonded Joint with Rubbery Adhesives
Study on the Numerical Simulation of the Resistance Spot Welding Process of
Magnesium Alloy
Study on Defect of 304 Stainless Steel Industrial Condensation Board in CO2
Laser Welding
A Rapid Process for Fabricating Microfluidic Devices with a Low-Cost UV
Curable Resin
3-D Finite Element Analysis on a Fillet Weld Sealing Joint in the
High-Pressure Hydrogenation Heat Exchanger
Mechanical Properties on the Welded Connection of Pipe and Hollow Spheres
Joints
Solid-State Dye-Sensitized Solar Cells Based on ZnO Nanorod Arrays by
Low-Temperature Chemical Bath Deposition
Research of Thermal Anchor Attachment for ITER Magnet Supports
Effects of Ultrasonic Power on Bonding Strength of Anisotropic Conductive
Film Joint in Chip-on-Glass Assembly
Prediction and Application of Welding Residual Deformation of Steel Sheets
Fabrication of Fuel Reforming Catalytic Coatings for Hydrogen Production by
Cold Spray Technology
Automatic Hyperbaric Welding of Sub-Sea Pipelines Repair
Manual Self-Propagating High-Temperature Synthesis Welding of 45 Steel
Effects of Rar